![]() These results have been replicated using a PCE-AC68. For this reason, I decided to run this test for multiple hours throughout the last week and indeed, the router struggles keeping a constant throughput, delivering a pathetic average of about 200 Mbps when it was positioned near the antenna (if I increase the distance, the speed falls even lower). UPDATE : This is the second time I fully test the Asus RT-AX58U and the first time I tested it, I used a client equipped with an Asus PCE-AC88 and the throughput was not stable – it would run up to 800+ Mbps and then I noticed that it would sometimes fall underneath 100 Mbps and then back up (5GHz, on either 80 or 160MHz). It’s worth mentioning that the router makes use of Roaming Assist to drop the connection in case the RSSI falls below a certain threshold and there’s support for Smart Connect. There is also the Ethernet Backhaul which can make a difference for a dual-band mesh system – the bandwidth is less affected than when it has to handle both the inter-node communication and the client connection. That being said, the AiMesh does function in a similar manner to the other proprietary implementations, allowing the creation of optimized paths between multiple nodes (the routers) and one of the most important characteristics is the self-healing ability, which, in case a node fails, re-routes the data through the closest and least congested node available (this property can be seen in action when there are more than two nodes connected). I have tested AiMesh using an Asus RT-AC68U and an Asus RT-AC86U and the results weren’t that great (I also had some problems getting the two device to work together), but the RT-AC68U is old hardware and I assume that the RT-AX58U will work a lot better with the RT-AC86U (I will test this config soon). Lastly, I have to mention the support for AiMesh, a technology that allows multiple compatible ASUS routers to interconnect and create a mesh network (just like the Google WiFi, Eero WiFi or Netgear Orbi). If you still need help leave a comment below and I’ll try to help.Another significant improvement over the last gen is the Target Wake Time (TWT) feature which has the role of creating a scheduled wake time for each client based on the expected traffic, therefore conserving the battery life for 802.11ax IoT client devices (this is going to be useful only if the manufacturers aren’t requesting tons of info continuously from their devices, as they usually do) – one issue with the implementation of this feature on the RT-AX58U is that a laptop that’s not connected to a power source, will have its bandwidth severely limited (even if you disable this feature in the interface). This whole guide might seem a bit complicated, but it’s really easy to set up if you follow these steps carefully, Access the router interface, go to the WOL section and remotely start the PC you’ve configured earlier.The computer you took with you on your vacation is now on the same local network as your own router. Connect to that VPN using the external IP of the home router.Configure a VPN network server on your own router.I won’t go into details in this article, but it basically goes like this: Most likely you’ll want to turn on a computer remotely from the Internet to do some work, and that’s totally possible, even if you’re not on the same network with the router. When is WOL useful, you may ask? Well, if you’re in the other room and don’t feel like getting up from the couch to press the Power button. What If You Want to Turn On Remotely a Computer From the Internet? If you plan to access it remotely you’ll need to wait for it to completely boot up. Your computer will start up just like if you had pressed the Power button. Get The MAC Address of The Network Card Connected to The Router In my case, the NIC name is “Intel NIC 1000Mb” in the image below. If you didn’t rename it previously it will match the card name from Device Manager. On top of the page is a small schematic with your computer, a globe representing the Internet, and your network card linking them together. Open the Start menu and type Network status.Ģ. Note: you can configure all NICs to enable WoL, but only the one connected to the router will be able actually to wake up the computer.ġ. Find the Correct Network Card (NIC) Connected to the Routerĭo you have more than one network card, as I do? There’s an easy way to figure out which one you must configure for WOL. You may also need to do a bit of detective work to figure out which network card is the correct one if you have more than one NICs. You now need to configure the router to wake up the correct computer. Your computer will wake up pretty much immediately after a shutdown, trust me. Note: If you don’t check the Magic Packet box the computer will wake up automatically when any data package is received.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |